Examples

  • Each and every Polyline must be drawn as LWPOLYLINE.
  • Every closed polyline must contain a text inside or on the same layer.
    This text will be used as the name of that polyline. As far as possible this name should be unique.

1. _Amalgamation

  • Description: – Draw a continuous poly around the plots you want to amalgamate.

Amalgamation contains more than one plot amalgamated together.
All entities having amalgamation as their container entity should be uniquely present in each amalgamation.
i.e. suppose there is a road widening in the Plot then the poly of road widening should be different for each amalgamation. ( for amalgamation, draw plot 1,plot 2,plot 3 on plot layer and amalgamated plot AmalPlot 1, on amalgamation layer overlapping plot 1.)

  • Verification : It Should Overlap with _PlotBoundary.
  • Shortcut Command : – AMLG
  • How to draw :

2. _Amenity

·         Description: – Draw Amenity space as a closed polyline which is reserve for utilities, services and conveniences.

  • Basic Verifications : – It Should be Inside of PlotBoundary/ SubDivision/ Amalgamation

·         Shortcut Command : – AMN

  • How to draw :

3. _ArchProj

  • Description : – This layer is used to represent various Architectural Projections in your Plan. Draw a closed Polyline for Architectural Projections. And mark it using Mark->Projection from PreDCR menu, according to requirements. Canopy/porch will come in plot & other projections will come with floor plans.
  • Basic Verifications : – It should be inside floor/NetPlot
  • Shortcut Command: – AP.
  • How to draw : –

4. _VentilationShaft

  • Description : – Draw ArtiVentilation shaft/duct area as a closed Polyline with Text. Inside FSIArea on _ArtiVentiShaft Layer. Only those shafts from which ventilation for habitable room is not taken should be drawn on this layer.
  • Basic Verifications : – It Should be Inside of ResiFSI/ Parking/ Section/ PropWork/ Terrace/ CommFSI/ IndFSI/ SpecialUseFSI
  • Shortcut Command: AVS.
  • How to draw : –

5. _Balcony

  • Description : – Draw a balcony as a closed polyline which is a horizontal projection including parapet to serve as a sitting out place. Name of balcony must be inside and on _Balcony layer.
  • Basic Verifications : – It Should be Inside of Floor/ NETPLOT
  • Balcony can be present in :
Plot: It must overlap with PWork(if not enclosed)
Floor: It must overlap ResiFSI.
  • Shortcut Command : – BL
  • How to draw : –

6. _ BLDGBLOCK (in layout)

  • Description : –If you are submitting sub-division/amalgamation layout along with proposal for building permission also. Then you should draw sub-div/amal. layout on different drawing sheet and proposed building drawings on different drawing sheet. In this case, tentative block of building should be drawn on ‘_BLDGBLOCK(in layout)’ just for referring the presence of building in sub-div. or amal. Plot
  • Basic Verifications : – It Should be Inside of SubDivision/ Amalgamation
  • Shortcut command : – BLDBLK
  • How to draw : –

7. _Building

  • Description: Building is used to group all floor plans of the same building.   Draw a closed poly enclosing all the floor plans and section of the same building on _Building layer. Note: As written above, dimension or area of this building poly has no meaning in AutoDCR. This is just an logical group of all floors of the same building. If the building plan of multiple PWorks or wings is same then building name shall be as given in table below.

Building names can be.

1  “A(Monarch)” PWork “A” has building plan “Monarch”.
2  “A,B(Monarch)” or “A&B(Monarch)” Wings A, B have same building plan “Monarch”.
3  “A-C(Monarch)” Wings A, B, C have same building plan “Monarch”.
4  “A1-A3(Monarch)” Wings A1, A2, A3 have same building plan “Monarch”.
  • Basic Verifications: – Entity must contain following entities Floor & Section.
  • Shortcut Command : – BLD
  • How to draw: – What Building poly will have? Building poly will enclose all the floor plans in that building along.

   8. _Carpet Area

  • Description: – Draw carpet area as a closed polyline which is a net usable floor area within a building excluding that covered by the walls or any other areas specifically exempted from floor space index computation in these regulation.
  • Basic Verifications: – It should be Inside of ResiFSI/ CommFSI/ IndFSI/ SpecialUseFSI. It Should contain Room  Inside  it
  • Shortcut command : – CPT.
  • How to draw : –

9. _Chowk

  • Description : – Draw a chowk as a closed polyline which is an enclosed space permanantly open to the sky within a building at any level. From chowk we take ventilation for habitual rooms.
  • Basic Verifications : – Should be Inside of :  PropWork/ ResiFSI/ Parking/ Terrace/ CommFSI/ IndFSI/ Section/ SpecialUseFSI
  • Shortcut Command : – CWK.
  • How to draw : –

10. _CommFSI

  • Description: Commercial FSI : –  Draw a CommFSI as a closed polyline which is the area covered by a building on all the floors. This FSI polyline mainly used for commercial use bldg.
  • Basic Verifications : – It Should be Inside of Floor. It Should contain CarpetArea  Inside  it
  • Shortcut Command : – CMFS.   
  • How to draw : –              

11. _CompoundWall

  • Description : – Open polyline of compound wall to be drawn on proposed compound wall with text started with compound wall height. E.g. 1.5m. high Compound Wall
  • Basic Verifications : –
  • Shortcut Command : – CW.
  • How to draw : –

14. _Door

  • Description: – Door is a closed Polyline Which is drawn on “_Door” layer. Also you can insert a particular size poly for Door using Insert->Door from PreDCR menu.
  • Basic Verifications: – It should be Inside of Floor/ CarpetArea. It Should Overlap with Room/ CarpetArea/ Staircase/ Passage/ Terrace/ Balcony/ SubStructure.
  • Shortcut Command: – DR.
  • How to draw : –

14. _ElecLine

  • Description: – Electric Line: Electric line will be present in the layout plan and shall pass through plot entity as a non closed polyline.
  • Name electric line shall start with its voltage capacity and text insertion point shall lie on its polyline.

  For e.g. 33 KV High Tension Line

  • Basic Verifications : –
  • Shortcut Command: – L1.
  • How to draw : –

15. _ExStructure

  • Description: – Draw a Exstructure as a closed polyline which is a building or structure existing authorized before the commencement of these regulation. And mark it using Mark -> Existing structure as ‘To be demolished’ or ‘To be retained’.
  • Basic Verifications: – It should be Inside of PlotBoundary.
  • Shortcut Command: – EX.
  • How to draw :-

16. _Floor

  • Floor: – Draw a Floor as a closed polyline to the boundary of the lower surface in a story on which one normally walk in a building and including mezzanine floor also. The floor at ground level with a direct access to a street or open space shall be called the ground floor, the floor above it shall be termed as Floor 1 with the next higher floor being termed as Floor 2 and so on upward. For giving the name of each floor use the assign named option from the PreDCR menu. Also draw each floor separately. While giving name to the typical floor then use a Typical option from Assigned name -> Floor name option from PreDCR menu bar.
  • Basic Verifications: – It Should be Inside of Building. It Should contain  ResiFSI/ CommFSI/ Terrace/ Parking/ IndFSI/ Staircase/ SpecialUseFSI  Inside  it
  • Shortcut Command : – FLR
  • Reference Circle: – All Floor polies must contain a circle with its center on common point for whole building on layer “_ResiFSI”. Usually it can be placed inside either Common Lift or stair/Inner Chowk as their locations are common for all floors.
  • Floor Name : – Floor name will be taken from text inside floor poly and on same layer.

  A floor plan is automatically associated/linked by AutoDCR software with one or more floor section poly in Section plan. This is done by matching name of Floor Plan and FloorInSection so both must be same.

Typical Floor Non-Typical
“TYPICAL” X “FLOOR PLAN”X: Floor numbers in specific format (, or & or -) X “FLOOR PLAN” X: Direct Floor’s Name
e.g.: TYPICAL 1,2 FLOOR PLAN TYPICAL 1-4 FLOOR PLAN TYPICAL 2&3 FLOOR PLAN e.g. GROUND FLOOR PLAN FIRST FLOOR PLAN SECOND FLOOR PLAN
  • How to draw :

17 _FloorInSection

  • Description: – Draw a Floor In Section as a closed polyline which is the height of that floor (slab top to slab top) This poly only used for checking floor height. For assigning the name of FloorInSection then used Assigned name option for PreDCR tool menu.
  •   Name of each floor section will be same as of floor in plan.
  •   For one typical floor plan multiple floor section will be there.
  • For e.g. for one typical floor plan for 1-3 floors there will three sections shall be drawn with name “First Floor Plan”, “Second Floor Plan” and “Third Floor Plan” respectively.
  • Basic Verifications: – It should be Inside of Section.
  • Shortcut Command: – SECF.
  • How to draw : –

                                        `

18. _GroundLevel

  • Description: – Draw the Ground level line as open polyline in section .It is used for checking a total building height from this line.
  • Basic Verifications: – It Should be Inside of Section.
  • Shortcut Command: – GL.
  • How to draw : –

19. _IndFSI

  • Description: – Draw a IndFSI as a closed polyline ( area key plan line in the submission drg) which is the area covered by all the floors. Industrial building means building or part thereof wherein products or material are fabricated , assembled or processed such as assembly plants, laboratories , power plans, refineries, gas plants, mills, dairies and factories. This polyline should be excluding balcony & terraces area.
  • Basic Verifications: – It Should be Inside of Floor. It Should contain CarpetArea  Inside  it
  • Shortcut Command: – IFSI.
  • How to draw : –

20. _IntDPRoad

  • Description : – Draw existing or proposed D. P. (Development Plan) road or T. P. (Town Planning) Road when inside/intersected with plot. While giving name start text with road -width.

E.g. 15m wide D.P. Road.

  • Basic Verifications : –
  • Shortcut Command : – R3.
  • How to draw : –

21. _IndZoneBoundary

  • Description: – Draw zonal boundary of industrial zone inside plot from where required margins are to be checked.
  • Basic Verifications : –
  • Shortcut Command: – IZB.
  • How to draw : –

22. _InternalRoad

  • Description : – Draw internal road with text specifying its width as shown in figure. And draw a center line. And type of layer of the center line must be center line (Type of the Layer).
  • Basic Verifications: – It Should be Inside of MainPlot. It Should Overlap with NETPLOT/ MainPlot/ IntDPRoad/ RoadWidening/ RightOfWay/ MainRoad/ InternalRoad
  • Shortcut Command: – R2.
  • How to draw : –

23. _Lift

  • Description: – Draw a Lift as a closed polyline which is a mechanically guided car, platform or transport for persons and materials between two or more levels in a vertical or substantially vertical direction. If fire lift are provided then use the marking of “Fire lift” option from Mark -> Lift -> Fire Lift . Fire Lift means a special lift designed for the use of fire service personnel in the event of fire or other emergency.
  • Basic Verifications : – It Should be Inside of  CommFSI/ ResiFSI/ IndFSI/ Terrace/ Parking/ Section/ PropWork/ SpecialUseFSI
  • Shortcut Command: – LFT.
  • How to draw : –

24. _LocationPlan

  • Description: – Location plan if any to be drawn on this layer. This is only for reference. No verifications are done by AutoDCR for this layer so not compulsory.
  • Basic Verifications : – It Should contain MainPlot  Inside  it
  • Shortcut Command: – LCP.

25._MainRoad

  • Description : – Draw a main road as a closed polyline which is abutting the plot. On the site that road is any type of road. such as any highway, street , lane, , over which the public have a right of passage or access or have passed and had access uninterruptedly for a specified period, whether existing or proposed in any schem. Road name start with its width only.
  • Basic Verifications : – It Should Overlap with MainPlot/ RightOfWay
  • Shortcut Command : – R1
  • How to draw : –

26. _MarginLine

  • Description : – No need to draw Margin Line, Just use Mark Margin tool for it. This layer is not provided for users. AutoDCR uses ‘_MarginLine’ layer for it’s own internal use.

27. _Nala

  • Description: – Draw Nala polygon on this layer.
  • Basic Verifications : –
  • Shortcut Command: – R4.
  • How to draw : –

28. _NDZ

  • Description: – No Development zone area if any inside plot to be drawn on this layer. And it should be drawn inside the plot with text on _NDZ layer.
  • Basic Verifications: – It Should be Inside of PlotBoundary.
  • Shortcut Command: – NDZ.
  • How to draw : –

29. _NETPLOT

  • Description : – No need to draw NETPLOT. This layer is not provided for users. AutoDCR uses ‘_NETPLOT ‘ layer for its own internal use.
  • How to draw : –

30. _NotInPossession

  • Description: – Plot area which is not in possession or which is not in proposal to be drawn as a closed polyline on this layer.
  • Basic Verifications : – It should either overlap with Existing Road or RoadWidening or should be Inside and overlapping with PlotBoundary.
  • Shortcut Command: – NIP.
  • How to draw : –

31. _Parking

  • Description : – Draw a parking poly as a closed polyline which is an enclosed covered or open area sufficient in size to park vehicles. This closed polyline shall contain a text on same _Parking layer. This text is treated as name of parking. Insert the parking by using a Insert-> Parking option.
  • Basic Verifications: – It Should be Inside of MainPlot/ Floor.
  • Shortcut Command: PK.
  • Parking Name: – This closed polyline shall contain a text on same _Parking layer. This text is treated as name of parking.

  On this layer, you can group and insert any number of parking

Parking Name
Car Large CP-L
Car Small CP-S
Scooter SC
Cycle CY
Visitor’s Parking ( Car ) VP
  • How to draw : –

32._Passage

  • Description: – A closed polyline on _Passage represents a passage. It is a common passage or circulation space including a common entrance hall. This closed polyline contain a text. This text must be on “_Passage” layer. This text is treated as name of closed polyline.
  • Centre Line : –All Passage poly must contain an Open Polyline inside that closed poly representing centre  line on “_Passage” Layer. But line type of center line must be ‘Center line’.
  • Basic Verifications: – It should be Inside of CommFSI/ ResiFSI/ Parking/ PropWork/ IndFSI/ SpecialUseFSI. It Should Overlap with CarpetArea/ Passage/ StairCase/ Lift
  • Shortcut Command : – PAS
  • How to draw : –

33._Pathway

  • Description: – Draw pathway as a closed polyline with text specifying its width.eg.1.5 m. wide pathway.
  • Basic Verifications: – It should be Inside of PlotBoundary.
  • Shortcut Command: R6.
  • How to draw :-

34._PlotBoundary

  • Description: – Draw a Plot poly as a closed polyline which is a parcel or piece of land enclosed by definite boundaries. A Plot will contain all Proposed Works (buildings, wings), open space, Internal Roads, Parking etc. The overall Plot Entity represent a Plan, AutoDCR refers it as ‘Layout Plan’. The overall Plot Entity represent a Plan, AutoDCR refer it as “Layout Plan“.
  • Basic Verifications: – It Should Overlap with MainRoad/ IntDPRoad/ RightOfWay. It Should contain PropWork  Inside  it
  • Shortcut Command: PLT
  • How to draw :-

35._Podium

  • Description : – Podium shall be drawn on ‘_Podium’ layer as a closed polyline. Podium should be inside plot covering proposed works if any.
  • Basic Verifications: – It should be Inside of PlotBoundary/ Floor.
  • Shortcut Command: POD.
  • How to draw :-

36._PropWork

  • Description: – Proposed Work is a building profile/outline and shall be drawn inside plot. all detail Building plans (inside building polyline ) of all PWork( inside plot polyline) is associated/linked automatically by Auto-DCR by matching its name.

  So for proper association it is required to follow specific standard as given.

  XY (Z)
  X is Wing name.
  Y is wing number.
  Z is Building name.

  • For example if there are four wings A1,A2 & B1,B2 in building named “Monarch” then proposed work  names shall be –

  A1 (Monarch), A2 (Monarch)
  B1 (Monarch), B2 (Monarch)

  • Reference Circle: All PWork poly must contain two circles (of any size) with its center on common point for whole building. First on layer of any FSI and second on Layer “_Floor”. These reference circles to be inserted from PreDCR -> insert–>Direction ref circles at the same location in all the floors as well as pwork in plot.  Usually they can be placed inside either Common Lift or Stair/Inner Chowk (because generally their location is same on all floors). Reference circles are used by the software for overlapping all floor plans.
  • Basic Verifications: – It should be Inside of NETPLOT/ MainPlot.
  • Shortcut Command: PW.
  • How to draw :-

37._RailLine

  • Description: – Railway line shall be drawn as a non closed polyline with some text indicating gauge of rail line over it.
  • Basic Verifications : –
  • Shortcut Command: – L2.
  • How to draw : –

38._Ramp

  • Description : – Draw a Ramp poly as a closed polyline in floor plans and/or plot and section. Naming convention for ramp is “—m. long and —m. high ramp-1”. give unique name to each ramp.
  • Basic Verifications: – It should be Inside of MainPlot/ Floor.  It Should Overlap with PropWork/ Podium
  • Shortcut Command: – RP.
  • How to draw : –

39. _RecreationalGnd

  • Description : – Draw recreational ground / Open space as closed polyline reserved as recreational space on this layer. With text on same layer.
  • Basic Verifications: – It should be Inside of NETPLOT/ PlotBoundary /Amalgamation / Subdivision.
  • Shortcut Command: – OPS.
  • How to draw : –

40. _RefugeArea

  • Description : – Refuse area to be drawn in plan as a closed polyline with text on this layer. Overlapped with FSI layer but outside the FSI poly.
  • Basic Verifications: – It should be Inside of Floor.
  • Shortcut Command: – RFG.
  • How to draw : –

41. _ReservArea

  • Description: – Reserved area ( Reservation area in Development plan) shall be drawn on this layer if present in proposal. This can be any area reserved for/by Authority for future.
  • Basic Verifications: – It should either overlap with MainRoad InternalDPRoad RightOfWay or should be Inside and overlapping with Plot Amalgamation SubDivision.
  • Shortcut Command:- RSA.
  • How to draw :-

42._ResiFSI

  • Description : – Draw a ResiFSI as a closed polyline which is the area covered by a building on all the floors. This FSI polyline only used for residential use building or floor. ResiFSI poly must be inside Floor poly.
  • Basic Verifications: – It should be Inside of Floor. It Should contain CarpetArea  Inside  it
  • Shortcut Command : – MFS
  • How to draw : –

43. _RightOfWay

  • Description: – Draw a closed polyline on “_RightOfWay” to represent a Right Of way and text inside it representing its width. Layer should be inside or intersecting with Plot poly.
  • Basic Verifications : – It Should contain CarpetArea  Inside  it
  • Shortcut Command: – ROW.
  • How to draw : –

44. _RoadWidening

  • Description: – Draw a road widening polyline as a closed polyline which the plot area is going to the road, that area should be drawn on this layer. It should be inside the plot polyline.
  • Basic Verifications: – It should be Inside of MainPlot. It Should Overlap with MainRoad/ IntDPRoad.
  • Shortcut Command: – R5.
  • How to draw : –

45. _Room

  • Description : – A closed polyline on _Room layer represents a room. This closed polyline contain a text. This text must be on _Room layer. Room to be marked by assigning them names using Assign Name-> room option from PreDCR menu.
  • Basic Verifications: – It Should be Inside of CarpetArea.
  • Shortcut Command: – RU.
  • How to draw : –

46._Sanitation

  • Description : – Draw any sanitation entities on this layer. (E.g. Water closet, Kitchen sink etc..) Mark those entities by using PreDCR -> Insert -> Sanitation.
  • Basic Verifications : –
  • Shortcut Command: – SND.
  • How to draw : –

47._Section

  • Description: – Draw a Section polyline as a closed poly of section boundary which contain all floors with stair cabin, Lift machine room, water tanks etc. as shown in the figure. Also write the name as “Section” in this section poly.
  • In this closed poly of section draw sections of all floors with stair cabin, inner Chowk, Lift machine room, Ventilation shaft, water tanks etc. as shown in the figure.
  • Also write the name as “Section” in this section poly.
  • This section poly will present inside the building poly.
  • Basic Verifications: – It should be Inside of Building.
  • Shortcut Command: – SEC.
  • How to draw : –

48. _Sewageline

  • Description: – Drain/Sewage Line: – Sewage line shall be drawn as a open polyline on this layer.
  • Basic Verifications : –
  • Shortcut Command: – L5.
  • How to draw : –

49. _SitePlan

  • Description : – Site plan if any to be drawn on this layer. This is only for reference. No verifications are done by AutoDCR for this layer. so not compulsory.
  • Basic Verifications : –
  • Shortcut Command : – STP

50. _SpecialUseFSI

  • Description: – FSI ploy for all other building uses like educational, institutional etc. except ResiFSI, CommFSI & IndFSI use should be drawn on this layer.
  • Basic Verifications: – It should be Inside of Floor. It Should contain CarpetArea  Inside  it
  • Shortcut Command: – SUF.
  • How to draw : –

51. _StairCase

  • Description : – StairCase: On this layer, Each StairCase poly shall have three lines for Flight Width, Intermediate Landing and Floor Landing on same layer. Mark these open polyline by using Mark-> Staircase option from PreDCR menu. Also draw in plan all the treads on this layer which is a open polyline.
  • This closed polyline contains a text. This text must be on _Stair layer. This text is treated as name of closed polyline. On this layer, Each StairCase poly shall have three lines for Flight Width, Intermediate Landing and Floor Landing on same layer This can be mark by tool Mark > StairCase > intermediate landing etc.
  • Basic Verifications : – It should be inside Floor / proposed work
  • Shortcut Command: – STR.
  • How to draw : –

52. _ SubDivision

  • Description: – In Subdivision one plot is divided into more than one Subdivision.
    All entities having subdivision as their container entity should be uniquely present in all Subdivisions of a Plot i.e. suppose there is a road widening in the Plot then the poly of road widening should be different for each Subdivision (subdivided plot).
    Ex. Here Plot 1 is divided into three Subdivisions. And also the Road Widening is divided into RoadW 1 and RoadW 2 for each Subdivision.

     (For subdivision, draw plot 1 on plot layer and subdivided plots like SubDiv 1, SubDiv 2 &   SubDiv 3 on sub-division layer overlapping plot 1.)

  • Basic Verifications : –
  • Shortcut Command : – SBD
  • How to draw : –

53. _SubStructure

  • Description: – Draw various substructures on “_SubStructure” layer as a closed polyline. And mark it according to the requirement as Mark -> Substructure -> Society Office, from PreDCR menu. Sub-structures can be drawn inside plot or in floor plans.
  • Basic Verifications: – It should be Inside of NETPLOT/ Floor.
  • Shortcut Command: – SSTR.
  • How to draw : –

54. _SurrenderToCorp

  • Description: – In case of accommodation reservation, the plot area or FSI to be surrendered to NMC is to be drawn on This layer. With text inside it.
  • Basic Verifications : – It Should be Inside of PlotBoundary/ Floor
  • Shortcut Command: – STC.
  • How to draw : –

55. _Tank

  • Description : – A closed polyline on _Tank layer represents a water tank. Under Ground tank can be drawn in Floor or Layout plan. If it is drawn in Floor plan then it should be at bottom of GROUND FLOOR. Overhead tank can be drawn in TERRACE FLOOR. Tank should be drawn as per internal size or dimensions. Both the tank also draw in section also.
  • Tank Name: – This closed polyline contain a text and must be in given format. This can also be done by tool Assign Name>Tank

  Tank Name+ Type +Capacity

Tank Type Text
Overhead water tank (O/H)
Underground water tank (U/G)

  For e.g.

  TANK-1 (O/H)

  TANK-2 (U/G)

  • Under Ground tank can be drawn in Floor or Layout plan. If it is drawn in Floor plan then it should be at bottom of GROUND FLOOR.
  • Overhead tank can be drawn in TERRACE FLOOR. Usually it is drawn on StairCase poly in TERRACE FLOOR.
  • Basic Verifications: – It should be Inside of NETPLOT/ Floor/ Section.
  • Shortcut Command: – TNK.
  • How to draw : –

56. _TempStructure

  • Description: – Area for temporary structures to be drawn as closed polyline with text on this layer.
  • Basic Verifications : –It Should be Inside of  PlotBoundary
  • Shortcut Command: – TMPS.
  • How to draw : –

57. _Terrace

  • Description: – Draw a Terrace as a closed polyline on _Terrace layer which is including parapet wall.
  • Terrace can be present in: 
 Plot: It must overlap with PWork
 Floor: It must be outside the ResiFSI.
  • Basic Verifications : – It Should be Inside of Floor/ NETPLOT
  • Shortcut Command: – TER.
  • How to draw : –

58. _UpperSetBack

  • Description: – Draw a closed polyline in plan as well as in proposed work which having setbacks.
  • Basic Verifications : –It Should be Inside of  PropWork/ Floor
  • Shortcut Command: – USB.
  • How to draw : –

59. _Void

  • Description : – If the space is not Chowk then it can be void. All ducts (where ventilation is not taken) and double height rooms can be drawn in void layer.
  • Basic Verifications : –It Should be Inside of CommFSI/ ResiFSI/ IndFSI/ SpecialUseFSI/ PropWork/ Terrace/ Parking
  • Shortcut Command: – VD.
  • How to draw : –

60._WaterLine

  • Description: – Draw a Water line as a open polyline to show Water supply.
  • Shortcut Command: – WL.
  • How to draw : –

61. _Window

  • Description: – Window is a closed Polyline Which is drawn on “_Window” layer. Also you can insert a particular size poly for Window using Insert->Window from PreDCR menu.
  • Basic Verifications : – It Should be Inside of  Floor/ Balcony/ CommFSI/ ResiFSI/ IndFSI/ SpecialUseFSI and It Should Overlap with Room/ CarpetArea/ Balcony/ StairCase/ Passage
  • Shortcut Command: – WND.
  • How to draw : –
Categories: Predcr

Leave a Reply

Your email address will not be published. Required fields are marked *