1. Create New Project (PDCRNWP): This command will Create New project for current drawing.
    Here you have to select Type of Project as
     Proposed Development.

Note: It is always compulsory to add your drawing to new Project.

  • Create AutoDCR Layers (PDCRCL): This command will create layers required for AutoDCR and as per the Project Type you have selected.
  • Fix Poly (PDCRPE): Use this command once on the final drawing which will process all the polyline on the PreDCR layer and remove extra vertices found on polyline. This command can be used before verifying the drawing using Verify commands.
  • Verify Drawing: This command will verify the current drawing as required by DCR specifications.

 a) Verify Close Entities (PDCRVD): Verify that LWPOLYLINE entities on the selected layers are closed and contain one text .

b) Verify All drawing (PDCRVT): Use this command to verify the layout and building level objects in the current drawing plan.
Major checks are as follows:

In the “Verify All Drawing Dialog” you can select the layout or building objects to be checked. Then to view the result press OK button. PreDCR will start checking all corresponding objects in the currently open drawing and then display the status as OK or list of failed objects in the dialog as shown in Figure. Failed Object Information. 

  • Check if these entities are drawn as closed LWPOLYLINE.
  • Name text is given to all objects.
  • Entities are placed exactly inside their parent objects (container).
  • Naming conventions are followed properly.

c) Objection List (PDCROLST): This command gives the list of all minimum required entities which are not there in your drawing. If all required entities found then it gives a message that “minimum required entities are present in drawing”.

5. Mark: Marking adds some extra meaning in entity. Following commands are provided to mark different   entities as per requirement.

  1. Mark->Stair Case-> No Of Flights (PDCRSC3F): Mark staircase which having a 3 or 4 flights.
    1. Mark->Stair Case->Fire Escape Staircase (PDCRSFES): Mark staircase as a Fire Escape Staircase.

Mark->Stair Case-> Fab /Spiral Staircase (PDCRSCFAB): Mark line inside staircase as a Fabricated or spiral staircase.

Mark-> Escalators (PDCRSCES): Mark Escalators which is on Staircase layer.

3.  Mark->Stair Case Landing–> Intermediate Landing (PDCRMIL): Mark line inside staircase as intermediate Landing.

Mark->Stair Case Landing->Flight Width (PDCRMFW): Mark line inside staircase as Flight Width.

Mark->Stair Case Landing->Floor Landing (PDCRMFL): Mark line inside staircase as Floor Landing.

  • Mark->Passage->Covered Passage->Free from FSI OR Taken in FSI (PDCRPOCP): Mark passage as a covered passage & it is taken in FSI or Free from FSI.

       Mark->Passage-> Open Corridor (PDCRPSUP): Mark passage as a Open Corridor.

      Mark->Passage->Normal (PDCRPSUP): Mark passage as a Normal.

      Mark->FSI->Road Widening (PDCRCONES): Mark Residential or Commercial FSI as Road           widening areas FSI.

Mark->FSI-> TDR (PDCRCONES): Mark Residential or Commercial FSI as TDR.

Mark->FSI-> Existing FSI (PDCRCONES): Mark Residential or Commercial FSI as Existing FSI.

Mark->FSI->Normal (Default) (PDCRUMFSI): Mark Residential or Commercial FSI as Normal FSI.

  • Mark->Carpet Area->Splitted Tenement (PDCRMSPLTT): Mark Carpet Area as Splitted tenement.

Mark->Carpet Area->Slum Development->Sale OR Rehab (PDCRUMFSI): Mark Residential or Commercial FSI as Slum Development & Mark Carpet Area for Sale or Rehabitation.

Mark->Carpet Area-> Normal (Default) (PDCRUMFSI): Mark Residential or Commercial Carpet Area as Normal Carpet Area.

  • Mark->Balcony->Enclosed Balcony (PDCRMENCBL): Mark Balcony as enclosed balcony.

Mark->Balcony->Unmark (Default) (PDCRUMENCBL): Unmark the marked balcony.

  • Mark->Projection– >

Mark->Projection->F.Bed (PDCRMBPROJ): Mark Projection as Flower Bed.

Mark->Projection->C.B. (PDCRMBPROJ): Mark Projection as Cubourd.

Mark->Projection->Chhajja/Cornice/Whether shade (PDCRMCJPROJ): Mark Projection as Chhajja/Cornice/Whether shade.

Mark->Projection->Canopy (PDCRMCBPROJ): Mark Projection as Canopy.

Mark->Projection->Loft (PDCRMLPROJ): Mark Projection as Loft in floor plan as well as in section .

Mark->Projection->Porch (PDCRMCPROJ): Mark Projection as Canopy.

Mark->Projection->Verandah (PDCRMVPROJ): Mark Projection as Varandah.

Mark->Projection->Garbage Shaft (PDCRMVPROJ): Mark Projection as Garbage shaft.

Mark->Projection->Refuse Chute (PDCRMVPROJ): Mark Projection as Varandah.

Mark->Projection->Ornamental Projection (PDCRMVPROJ): Mark Projection as Ornamental Projection.

Mark->Projection->Normal (Default) (PDCRUMPROJ): Mark Projection as Normal Architectural projection.

  • Mark->Road Widening->Taken In FSI (PDCRMRVIFSI): Mark When area of the road widening is taken  In FSI.

      Mark->Road Widening->UnMark (Default) (PDCRUMMR): Mark When area of the road widening is  Not  taken  In FSI.

  • Mark->Existing Structure ->To be demolish (PDCRMREXWD): Mark Existing structure as to be demolished.

Mark->Existing Structure->To be retained (PDCRMRMREXWC): Mark Existing structure as to be retained.

  • Mark->SubStructure->Electric  Meter Room (PDCRMER     ): Mark Sub Structure as an electric meter room.

Mark->SubStructure->Electric Sub-station (PDCRMTRAN): Mark Sub Structure as an Electric Sub-station.

Mark->SubStructure->Watchman cabin (PDCRMWMC): Mark Sub Structure as a Watchman cabin.

Mark->SubStructure->Society Office (PDCRMOR): Mark Sub Structure as a Society office.

Mark->SubStructure->Servant Quarter (PDCRMSQ): Mark Sub Structure as a servant quarter.

Mark->SubStructure->Sanitary Block (PDCRMSB): Mark Sub Structure as a sanitary block.

Mark->SubStructure ->Covered Garage (PDCRMGRJ): Mark Sub Structure as a covered garage when garage is covered.

Mark->SubStructure ->Open Garage (PDCRMGRJ): Mark Sub Structure as a Open garage when garage is not covered.

Mark->SubStructure -> Rain Water Harvesing (PDCRMRWH): Mark Sub Structure as a Rain Water Harvesting..

Mark->SubStructure ->A. C. Plant Room (PDCRMACR): Mark Sub Structure as a A.C. Plant Room.

Mark->SubStructure ->AHU (PDCRMACR): Mark Sub Structure as AHU to Air handling unit .

Mark->SubStructure ->Swimming Pool(PDCRMSWP): Mark Sub Structure as a Swimming Pool.

Mark->SubStructure ->Septik Tank / Soak pit (PDCRMSPT): Mark Sub Structure as a Septik Tank.

Mark->SubStructure ->Pump House (PDCRMPR): Mark Sub Structure as a Pump House

Mark->SubStructure ->Effluent Treatment Plant (PDCRMETP): Mark Sub Structure as a Effluent Treatment Plant.

Mark->SubStructure ->Dish Antenna Room (PDCRMDA): Mark Sub Structure as a Dish Antenna Room.

Mark->SubStructure ->Well (PDCRMWELL): Mark Sub Structure as a Well.

Mark->SubStructure ->Telephone Installation Room (PDCRMTRM): Mark Sub Structure as a Telephone room.

Mark->SubStructure ->Entrance Gate (PDCRMEG): Mark Sub Structure as a Entrance Gate.

Mark->SubStructure ->Fitness Center(PDCRMCSS): Mark Sub Structure as a Fitness Center.

Mark->SubStructure ->Suction Tank (PDCRMWB): Mark Sub Structure as a Suction Tank.

Mark->SubStructure ->Pavilion (PDCRMOCP): Mark Sub Structure as a Pavilion.

Mark->SubStructure ->Gymnasium (PDCRMTRM): Mark Sub Structure as a Gymnasium.

Mark->SubStructure ->Club-House(PDCRMES): Mark Sub Structure as a Club-House.

Mark->SubStructure ->Dust Bin(PDCRMES): Mark Sub Structure as a Dust Bin.

Mark->SubStructure ->Milk Booth(PDCRMES): Mark Sub Structure as a Milk Booth.

      Mark->SubStructure ->Telephone Booth(PDCRMES): Mark Sub Structure as a Telephone Booth.

      Mark->SubStructure ->Letter Box(PDCRMES): Mark Sub Structure as a Letter Box.

      Mark->SubStructure ->Solar Water heater(PDCRMES): Mark Sub Structure as a Solar Water Heater.

  1. Mark->Margin (PDCRMRGN):Use this command to define or mark the front, sides and rear margins of the plot. .

6. Insert

  1. Insert->Parking-> Car L (2.5×5.5) (PDCRICP) -> Use this command to insert car-parking poly of size 2.5m.X5.5m. at selected point.

Insert-> Parking->Car S (2.3×4.5) (PDCRICP) -> Use this command to insert car-parking poly of size 2.3m.X5.5m. at selected point.

  • Insert-> Parking-> Scooter (PDCRISP) ->Use this command to insert Scooter parking poly at selected point.
    • Insert-> Parking-> Cycle (PDCRICY) ->Use this command to insert Cycle parking poly at selected point.

            4.   Insert->Parking->Visitors Parking->Car (PDCRIVP) -> Use this command to insert visitor car parking poly (2.3×4.5) at selected point

             6.  Insert->Parking-> Loading/Unloading(PDCRIVP) -> Use this command to insert Loading/Unloading parking poly at selected point

             7. Insert->Door (PDCRIDRNAM):Use this command to insert door poly at selected point and with specified size given by user. As soon as you use this command the following Dialog appears. 

8. Insert->Window (PDCRIWNDNAM): Use this command to insert window poly at selected point and with specified size given by user.

9. Insert->Sanitation Text (PDCRIWC): Use this command to insert sanitation text at selected point. Ex.  Water closet ,  Urinal , Wash basin etc………. which is drawn on “_Sanitation” layer, then insert text by using sanitation text marking from insert menu.

           10. . Insert->Direction Reference Circle (PDCRIWC): Use this command to insert direction reference circle. Insert these circles in all the floor plans as well as in proposed work at the same & common place (e.g. Lift or Stair) of all the floors.

          11. Insert->Tree (PDCRIWC): Use this command to insert tree.

7. Assign Name: – There are few naming conventions required by AutoDCR, for which PreDCR provides the following tools:

  1. Assign Name->Building and proposed works (PDCRBLDPWNL): Use this command to give name for building poly and its associated proposed works.
  • Assign Name->Tank (PDCRTNKNAM): Use this command to give name for Tank poly and its corresponding tanks.

Fill in the dialog and select the tank poly drawn in plan and the same drawn in section

  • Assign Name->Room (PDCRASRUN): Use this command to give different names for Room poly.
  • Assign Name->Floor Name  (PDCRASFLRNAM): Use this command for assigning name to a floor poly and it’s corresponding  floor in section poly in section.
Categories: Predcr

Leave a Reply

Your email address will not be published. Required fields are marked *